SpoofCard Caller ID Spoofing Calling Card
| "Trend STC Abs/Pvc Two Flute Router Cutter 6.3mm 25mm 1/4""" |
| "Used to slot and trim low melting point plastics such as ABS, Styrene and PVC. For maximum life these cutters are Solid Carbide. Two flute for fine finish. D: 1/4 inch D: 6.3 mm C: 63/64 inch C: 25 mm Shank Diameter: 1/4 inch OL: 65 mm Sha..."
Price: 30.95 |
| "Trend Two Flute Pocket Router Cutter 12.7mm 22mm 1/2""" |
| "A two flute cutters with extra long shanks. Deep grooving, rebating and mortising. Useful for template work when thickness of template restricts depth. Extra care must be taken to avoid breakage. D: 1/2 inch D: 12.7 mm C: 22 mm C2: 32 mm OL: ..."
Price: 30.95 |
| "Trend Rotatip Trimmer Bearing Guided Router Cutter 12.7mm 8mm 1/4""" |
| "Blades of cutters can be rotated through 180 degrees to give one new cutting edge. D: 1/2 inch D: 12.7 mm C: 8 mm OL: 57 mm B: 12.7 mm A: 90 degrees Shank Diameter: 1/4 inch Shank Diameter: 1/4 Dia Metric: 12.7 Dia Imperial: 1/2 Cut Len..."
Price: 37.95 |
| "Trend Router Plug Maker 16mm 16mm 1/4""" |
| "These plug cutters produces plugs to exactly fit counterbored holes produced by Ref. 62 & 63 group tools. Use at recommended speeds of 1000-20000 RPM. D: 16 mm C: 16 mm OL: 55 mm Shank Diameter: 1/4 inch Body: 22 mm Shank Diameter: 1/4 Dia M..."
Price: 44.95 |
| "Trend Rota-Tip Bearing Guided Cove Router Cutter 25mm 12.7mm 1/4""" |
| "Two blades. Replaceable tips are ideal for prolonged use on manmade materials. Low profile bearing fixing screw. D: 25 mm C: 12.7 mm OL: 52.5 mm Shank Diameter: 1/4 inch Shank Length: 30 mm Shank Diameter: 1/4 Dia Metric: 25 Cut Length Me..."
Price: 38.95 |
| "Trend CRAFTPRO Raised Panel Ogee Router Cutter 50mm 12mm 8mm" |
| "Panel raiser cutters for producing the panel for cabinet panelled doors, tool matches our range of profile scribers. Suitable for use on natural timber and MDF. For use in a router table only. Take several passes, increasing the depth with each pass...."
Price: 50.95 |
| "Trend Sunk Bead Router Cutter 22mm 10mm 1/4""" |
| "Gives a narrow appearance to a board edge. D: 22 mm C: 10 mm R: 3 mm OL: 39 mm Shank Diameter: 1/4 inch Shank Diameter: 1/4 Dia Metric: 22 Cut Length Metric: 10 Overall Length Metric: 39 Radius 1 Metric: 3..."
Price: 53.95 |
| "Trend Eccentric Single Flute Router Cutter 5mm 19mm 1/4""" |
| "Eccentric single flute cutters. Cutters are chosen for fast free cutting, when cutting speed takes preference over finish. Small diameter tools must be handled with care to avoid breakage. Single flute cutters should not be used in eccentric chucks. ..."
Price: 30.95 |
| "Trend Solid Tungsten Carbide Mini Burrs 6mm 12mm 3mm" |
| "Tooling for metal, glass reinforced plastic (GRP). plastic and wood. Carving, weld removal and drilling hole enlarging. Solid carbide head. For removing welds and burrs in metal, also hand engraving and sculpting wood and metal. D: 6 mm C: 12 mm..."
Price: 25.95 |
| "Trend Classic Style Bearing Guided Router Cutter 34.9mm 17.5mm 1/4""" |
| "Self-guiding cutters with the facility to change the profile by fitting a larger bearing & varying the depth. Supplied with two bearings. The larger bearing removes the bottom quirk. D1: 34.9 mm C: 17.5 mm B: 9.5,12.7 mm R1: 6 mm R2: 5 mm OL:..."
Price: 42.95 |
| "Trend Snappy Hex Shank HSS Drill Bit 3/16""" |
| "The HSS drill bit is gripped by a spring steel collet into the hex shaft. The hex shanks snap into the Quick Chuck. D: 3/16 inch D: 4.7 mm Shank Diameter: 1/4 inch hex Shank Diameter: 1/4 hex Dia Metric: 4.7 Dia Imperial: 3/16..."
Price: 5.49 |
| "Trend CRAFTPRO Round Over and Ovolo Router Cutter 25.4mm 12.7mm 1/2""" |
| "Self-guiding cutters for rounding over edges do not require a side fence. They are supplied with two bearings. Use the larger bearing for a round-over. If the cutter is lowered, a top quirk can be produced. Bullnose mouldings can also be produced by ..."
Price: 31.95 |
| "Trend Plastics and Engraving Mini Spiral Downcut Router Cutter 3mm 25mm 3mm" |
| "Range of small diameter shank cutters for CNC routers. Used for specialised applications including signmaking & PRB machining. Down-cut prevents feathered edges. Two flute. D: 3 mm C: 63/64 inch C: 25 mm OL: 65 mm Shank Diameter: 3 mm Shank..."
Price: 69.95 |
| "Trend Bearing Guided Ovolo and Round Router Cutter 51mm 25mm 1/2""" |
| "Self-guiding cutters for rounding over edges do not require a side fence. They are supplied with two bearings. Use the larger bearing for a round-over. If the cutter is lowered, a top quirk can be produced. A full round/bullnose for stair treads can ..."
Price: 65.95 |
| "Trend CRAFTPRO Single Flute Router Cutter 4mm 11.1mm 1/4""" |
| "Single fluted Tungsten Carbide straight cutter for fast free cutting. Single flutes should be chosen where speed and clearance rates are more important than the finish. Depth of cut should not exceed cutter diameter. D: 5/32 inch D: 4 mm C: 7/16..."
Price: 11.95 |
| "Trend Routaseal Silicon Sealing Strip Brown 10m" |
| "High grade silicon rubber weatherseal. Will stand temperature of -30 degrees to +200 degrees C. Recessed using a small 1/4"" hand router. Can be slid or tucked in from the top face. Compresses to approx. 3.5mm. Groove depth should be 3mm. Length: 1..."
Price: 40.95 |
| "Trend Easyset Bearing Guided Raised Bevel Combination Set 41mm 11mm 1/2""" |
| "These tools produce the same type of joint & use the same components as the combination PSC sets. Both parts of the joint are cut by only changing the cutter height. No reassembly of parts is required, to convert the tool from scribing mode to profil..."
Price: 100.95 |
| "Trend Replacement Cutter Bearings Metric OD 18mm" |
| "Bearings are shielded to prevent penetration of dust and grease packed for life. They should not be cleaned with solvent or lubricated as this will dissolve the grease and cause premature bearing failure. Scrape off any resin build-up. Always check t..."
Price: 10.95 |
| "Trend Chamfer Bearing Guided Router Cutter 31.8mm 12mm 1/2""" |
| "Ideal for newel posts and caps for stairs. Supplied with one bearing. D: 31.8 mm C: 12 mm C2: 16 mm B: 9.5 mm A: 45 degrees OL: 60 mm Shank Diameter: 1/2 inch Shank Diameter: 1/2 Dia Metric: 31.8 Dia Imperial: 1 1/4 Cut Length Metric: ..."
Price: 54.95 |
| "Trend CRAFTPRO Two Flute Straight Router Cutter 38.1mm 25mm 1/2""" |
| "Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising. Use on softwoods, hardwoods, MDF, plywood and chipboard. Cutter has a bottom cut feature. D: 1 1/2 inch D: 38.1 mm C: 25 mm OL: 66 mm Shank ..."
Price: 49.95 |
| "Trend Bearing Guided Rebate Set Router Cutter 24mm 12.7mm 1/4""" |
| "Popular rebate sets which include different size bearings for a choice of rebates. Ease of setting-up and accurate depth of cut. Ideal for rebating straight and shaped work pieces. Ideal with delicate applications such as musical instrument productio..."
Price: 56.95 |
| "Trend Aluminium UPVC Single Flute Helical Upcut Cutter 3mm 12mm 1/4""" |
| "Single flute helical for drilling and slotting, cutting aluminium anodised duralium and uPVC plastic. Cutters are designed to plunge and machine or mill lateral slots. All aluminium tooling should be used with a coolant, wax stick or lubricant. Mater..."
Price: 20.95 |
| "Trend CRAFTPRO Two Flute Straight Router Cutter 25.4mm 25mm 1/2""" |
| "Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising. Use on softwoods, hardwoods, MDF, plywood and chipboard. Cutter has a bottom cut feature. D: 1inch D: 25.4 mm C: 25 mm OL: 64 mm Shank Diame..."
Price: 25.95 |
| "Trend Chamfer V Groove Router Cutter 12.7mm 10.3mm 8mm" |
| "Use for bevelling, chamfering and for producing mortar grooves. Approximately 1.0mm flat will be found on the nose. D: 1/2 inch D: 12.7 mm C: 10.3 mm C2: 11.9 mm A: 60 degrees OL: 47.5 mm Shank Diameter: 8 mm Shank Diameter: 8 mm Dia Met..."
Price: 24.95 |
| "Trend Acrylic Single Flute Engraving Router Cutter 6.35MM 19mm 1/4""" |
| "Single flute for fast cutting. Specially ground for cutting acrylic. D: 1/4 inch D: 6.3 mm C: 19 mm Shank Diameter: 1/4 inch OL: 51 mm Shank Diameter: 1/4 Dia Metric: 6.3 Dia Imperial: 1/4 Cut Length Metric: 19 Cut Length Imperial: 3/4..."
Price: 44.95 |
| "Trend Chamfer V Groove Router Cutter 25.4mm 13mm 1/2""" |
| "Use for bevelling, chamfering and for producing mortar grooves. Approximately 1.0mm flat will be found on the nose. D: 25.4 mm C: 13 mm C2: 17.5 mm A: 45 degrees OL: 57 mm Shank Diameter: 1/2 inch Shank Diameter: 1/2 Dia Metric: 25.4 Dia..."
Price: 48.95 |
| "Trend TRADE RANGE Staggered Mortise Router Cutter 16mm 1/2""" |
| "For deep mortising & grooving giving good chip clearance. Will plunge to a depth of 70mm in a number of passes. Features 2mm micrograin Tungsten Carbide tips, for cutting the most abrasive materials to give extra long life. PTFE coated, indicated by ..."
Price: 35.95 |
| "Trend Snappy Hex Shank Masonry Drill Bit 7mm" |
| "Tungsten Carbide Tipped masonry drill to suit wall plugs. D: 7 mm OL: 123 mm Flute length: 69 mm Shank Diameter: 1/4 inch hex Shank Diameter: 1/4 hex Dia Metric: 7 Overall Length Metric: 123..."
Price: 4.49 |
| "Trend Ovolo Rounding Over Router Cutter 18mm 10mm 1/4""" |
| "Some Ovolo cutters can be used with radius cutters, to make rule joints. D: 18 mm D2: 12 mm C: 10 mm R: 3 mm OL: 38.6 mm Shank Diameter: 1/4 inch Shank Diameter: 1/4 Dia Metric: 18 Dia2 Metric: 12 Cut Length Metric: 10 Overall Length ..."
Price: 34.95 |
| "Trend Eccentric Single Flute Router Cutter 6.3mm 12.7mm 1/4""" |
| "Eccentric single flute cutters. Cutters are chosen for fast free cutting, when cutting speed takes preference over finish. Cutters with prefix S are Solid Carbide. Cutters of 2.0mm diameter and below should have a maximum of 1.0mm depth of cut per pa..."
Price: 18.95 |
| "Trend CRAFTPRO Radius Router Cutter 12.7mm 19mm 1/2""" |
| "These cove style cutters with two flutes, give radiused grooves for decorative panel finishes and board edges. For deep channels, take a series of passes. DIMENSIONS: D1: 1/2 inches D1: 12.7 mm C: 3/4 inches C: 19 mm OL: 86 mm R1: 6.3 mm S..."
Price: 26.95 |
