SpoofCard Caller ID Spoofing Calling Card
| "Trend Aqua 109 Weatherseal Strip White 25m" |
| "Weather strip is fitted into the window frame aperture using four cut lengths. It is important to create tight butt or notched joints to ensure high levels of window performance. Joints can be enhanced by the application of a small amount of silicone..."
Price: 75.95 |
| "Trend Bearing Guided Bevel Trimmer Router Cutter 29mm 13mm 1/4""" |
| "Cut a wider edge line, at an angle of 60 degrees. A 16mm bearing is supplied as standard. A larger 19mm bearing will spread the wear of the cutting edges. D: 29 mm C: 13 mm A: 60 degrees B: 16 mm OL: 55 mm Shank Diameter: 1/4 inch Shank Di..."
Price: 41.95 |
| "Trend Replacement Cutter Bearings Metric OD 35mm" |
| "Bearing for slotting systems. Ball bearings should be wiped clean, not dipped in solvent. Prevent resin build-up by cleaning with wire brush. OD: 35 mm ID: 12 mm Thickness: 8 mm Cut Length Metric: 8 Bearing Dia Metric: 35 Sawbore: 12..."
Price: 11.95 |
| "Trend Cove Bearing Guided Router Cutter 19.1mm 14.3mm 1/4""" |
| "The two bearings supplied offer the means of cutting different depths of mouldings. D: 3/4 inch D: 19.1 mm C: 14.3 mm B: 9.5 mm B2: 12.7 mm R: 3/16 inch R: 4.8 mm OL: 51 mm Shank Diameter: 1/4 inch Shank Diameter: 1/4 Dia Metric: 19.1 D..."
Price: 42.95 |
| "Trend CRAFTPRO Bearing Guided Classic Broken Ogee Router Cutter 22mm 10mm 8mm" |
| "Ideal for following template. It is advisable that the template is at least 5mm thicker than the cut length of the tool. D: 22 mm C: 25/64 inch C: 10 mm B: 22 mm R: 2.4 mm OL: 61 mm Shank Diameter: 8 mm Shank Diameter: 8 mm Dia Metric: 2..."
Price: 38.95 |
| "Trend Chamfer V Groove Router Cutter 19.1mm 9.2mm 1/4""" |
| "Use for bevelling, chamfering and for producing mortar grooves. Approximately 1.0mm flat will be found on the nose. Is ideal for imitating 'V' jointed tongue and groove on man-made board. D: 3/4 inch D: 19.1 mm C: 9.2 mm C2: 13 mm OL: 45 mm A..."
Price: 26.95 |
| "Trend Single Flute Pocket Router Cutter 7.9mm 19mm 3/8""" |
| "A single flute cutters with extra long shanks. All the single flute tools have recessed shanks to allow deeper cutting. Deep grooving, rebating and mortising. Useful for template work when thickness of template restricts depth. Extra care must be tak..."
Price: 27.95 |
| "Trend Two Flute PTFE Coated Non Stick Router Cutter 12.7mm 25mm 1/2""" |
| "Gives a clean finish to abrasive materials such as chipboard, MDF, plywood and certain hardwoods. For housing, grooving and mortising. Features 2mm micrograin Tungsten Carbide tips, for cutting the most abrasive materials to give extra long life. PTF..."
Price: 19.95 |
| "Trend Up Down Shear Router Cutter 12.7mm 38.1mm 1/2""" |
| "Tungsten Carbide Tipped. Two flute cutter with tips sheared up and down, giving a fine finish. For trimming veneered and double-faced boards, plywoods and natural timbers. These cutters have the action of pushing the chips towards the middle of the b..."
Price: 43.95 |
| "Trend Bearing Guided Trimmer Router Cutter 12.7mm 38.1mm 1/2""" |
| "Self-guiding trimmers with bearings mounted on end of cutter. For trimming plastic or plywood overlay. For copy profiling, use the bearing to follow a template or base edge of board. An approximate 3mm overlap should be left before copy profiling. Wh..."
Price: 41.95 |
| "Trend STC Mini Engraver Conical Radius Wood and Plastics 3mm 15mm 4mm" |
| "Range of small diameter shank cutters for Mini CNC router carving machines. For carving. Two flute upcut spiral. DIMENSIONS: D1: 3 mm C: 15 mm R1: 0.25 mm A: 6 degrees OL: 50 mm Shank Diameter: 4 mm For material: Wood, Acrylic, ABS Preset ..."
Price: 35.95 |
| "Trend Snappy Hex Shank Masonry Drill Bit 12mm" |
| "Tungsten Carbide Tipped masonry drill to suit wall plugs. D: 12 mm OL: 150 mm Flute length: 95 mm Shank Length: 1/4 inch hex Shank Diameter: 1/4 hex Dia Metric: 12 Overall Length Metric: 150..."
Price: 5.95 |
| "Trend Snappy Metric Tap 3.5mm" |
| "For use in torque control screwdrivers on metals and plastics. Shank Diameter: 1/4 inch hex Tap size: M3.5 x 0.6 Shank Diameter: 1/4 hex Dia Metric: M3.5 Type or Grade: for M3.5..."
Price: 15.95 |
| "Trend STC Spiral Upcut Router Cutter 9.5mm 32mm 1/2""" |
| "Ideal for use in CNC machines and for fixed head routing applications, can also be used in portable routers. Feed rates range from 5- 10m/min of 18000 - 24000 RPM. Ideal for hardwoods and abrasive material. Fine finish. Up-cut prevents burning in plu..."
Price: 90.95 |
| "Trend CRAFTPRO Bearing Guided Overlap Trimmer Router Cutter 12.7mm 25.4mm 1/4""" |
| "This 'roughing' trimmer, leaves an overhang of 3mm, for secondary final trim. D: 1/2 inch D: 12.7 mm C: 1 inch C: 25.4 mm B: 19.1 mm E: 3.2 mm A: 90 degrees OL: 81.5 mm Shank Diameter: 1/4 inch Shank Diameter: 1/4 Dia Metric: 12.7 Dia..."
Price: 25.95 |
| "Trend Lip and Spur Two Wing Machine Bit 20mm" |
| "These machine bits have two wings, two scribers and a centre point. Tungsten carbide tipped for extensive drilling of particle boards, and plastics of soft to medium density. The scribe gives a very clean entrance hole. Not for use on hard dense mate..."
Price: 51.95 |
| "Trend Replacement Cutter Bearings Metric OD 22mm" |
| "Bearings are shielded to prevent penetration of dust and grease packed for life. They should not be cleaned with solvent or lubricated as this will dissolve the grease and cause premature bearing failure. Scrape off any resin build-up. Always check t..."
Price: 11.95 |
| "Trend CRAFTPRO Chamfer Bearing Guided Router Cutter 51mm 19mm 1/2""" |
| "Self-guiding chamfer/bevel cutter. Bearing follows the board beneath. D: 51 mm C: 19 mm B: 12.7 mm A: 45 degrees OL: 72.5 mm Shank Diameter: 1/2 inch Shank Diameter: 1/2 Dia Metric: 51 Cut Length Metric: 19 Overall Length Metric: 72.5 ..."
Price: 40.95 |
| "Trend Pierce and Trim Two Flute Router Cutter 12.7mm 30mm 1/2""" |
| "Combination pierce and trim cutters. Pierce and cut out apertures in laminate worktops. Base of the cutter acting as a guide follower. D: 1/2 inch D: 12.7 mm C: 30 mm OL: 87 mm Shank Diameter: 1/2 inch Shank Diameter: 1/2 Dia Metric: 12.7 ..."
Price: 40.95 |
| "Trend TCT Cylinder Boring Bit 203 Series Left Hand Rotation 20mm" |
| "Tungsten carbide tipped boring bit with centre point, two cutting edges and two spurs. Suitable for drilling hinge holes in natural wood and man-made boards (including paper/plastic coated and veneered). Boring bits have a cylindrical shank with flat..."
Price: 48.95 |
| "Trend Dovetail Router Cutter 13.2mm 13mm 1/4""" |
| "For dovetail joints and sliding dovetails. To suit user preference, the table shows angles from the horizontal and the profiles show angles from the vertical. D: 13.2 mm C: 13 mm A: 103 degrees OL: 55 mm Shank Diameter: 1/4 inch Shank Diamete..."
Price: 29.95 |
| "Trend Quad Groover Blade 47.6mm 4.8mm 1/2""" |
| "Replacement blade for QUADX1/2TC. D: 1 7/8 inch D: 47.6 mm E: 12.8 mm Kerf: 4.8 mm No. of Teeth: 2 Dia Metric: 47.6 Dia Imperial: 1 7/8 Rebate Metric: 12.8 Saw Kerf Metric: 4.8 Saw Teeth: 2..."
Price: 24.95 |
| "Trend Two Flute PTFE Coated Non Stick Router Cutter 15mm 25mm 1/2""" |
| "Gives a clean finish to abrasive materials such as chipboard, MDF, plywood and certain hardwoods. For housing, grooving and mortising. Features 2mm micrograin Tungsten Carbide tips, for cutting the most abrasive materials to give extra long life. PTF..."
Price: 23.95 |
| "Trend Pierce and Trim Two Flute Router Cutter 12.7mm 29mm 1/2""" |
| "Combination pierce and trim cutters. Pierce and cut out apertures in laminate worktops. Base of the cutter acting as a guide follower. D: 12.7 mm C: 31 mm C2: 29 mm OL: 108 mm Shank Diameter: 1/2 inch Shank Length: 34 mm Shank Diameter: 1/..."
Price: 37.95 |
| "Trend Replacement Cutter Bearings Metric OD 33.9mm" |
| "Bearing for slotting systems. Ball bearings should be wiped clean, not dipped in solvent. Prevent resin build-up by cleaning with wire brush. B: 33.9 mm Bore: 1/2 inches Bore: 12.7 mm Thickness: 9.3 mm Cut Length Metric: 9.3 Bearing Dia Metri..."
Price: 19.95 |
| "Trend CRAFTPRO Giuded Pierce and Trim Router Cutter 6.3mm 18mm 8mm" |
| "Cuts out apertures in laminate worktops. The nose of the cutter acts as a guide follower. D: 1/4 inch D: 6.3 mm C: 45/64 inch C: 18 mm OL: 77 mm Shank Diameter: 8 mm Shank Diameter: 8 mm Dia Metric: 6.3 Dia Imperial: 1/4 Cut Length Metr..."
Price: 16.95 |
| "Trend Bearing Guided Rebater Router Cutter 35mm 12.7mm 1/4""" |
| "Popular rebate sets, which include different size bearings for a choice of rebates. Ease of setting-up and accurate depth of cut. Ideal for rebating straight and shaped work pieces.When using bearing Ref. B95A, make two passes when a full depth of cu..."
Price: 61.95 |
| "Trend Bearing Guided Wavy Mould Router Cutter 32mm 18mm 1/2""" |
| "An interesting and attractive mould with a unique wavy effect, using chords of the radius. D: 32 mm C: 18 mm B: 12.7 mm R: 4 mm OL: 67 mm Shank Diameter: 1/2 inch Shank Diameter: 1/2 Dia Metric: 32 Cut Length Metric: 18 Overall Length M..."
Price: 44.95 |
| "Trend CRAFTPRO Bearing Guided Corner Bead Router Cutter 26mm 16mm 1/4""" |
| "Attractive edge moulds. A full corner bead can be produced by making a second pass at 90 degrees. D: 1 1/32 inch D: 26 mm D2: 22 mm C: 5/8 inch C: 16 mm B: 15.9 mm R: 4.8 mm OL: 70.5 mm Shank Diameter: 1/4 inch Shank Diameter: 1/4 Dia ..."
Price: 38.95 |
| "Trend Reed Edge Mould Bearing Guided Router Cutter 24mm 25mm 1/2""" |
| "Decorative edge moulds for shelf edges. D: 24 mm C: 25 mm B: 19 mm R: 2 mm R2: 6 mm OL: 75 mm Shank Diameter: 1/2 inch Shank Diameter: 1/2 Dia Metric: 24 Cut Length Metric: 25 Overall Length Metric: 75 Bearing Dia Metric: 19 Radius 1..."
Price: 69.95 |
| "Trend CRAFTPRO Slat Wall Router Cutter 30mm 7mm 1/2""" |
| "A 'T' slot cutters for clamping and hanging applications. Relief cut required. MEC mechanical feed only. D: 30 mm D2: 10.5 mm C: 7 mm R: 3 mm A: 119 degrees OL: 55.5 mm Shank Diameter: 1/2 inch Shank Diameter: 1/2 Dia Metric: 30 Dia2 Metr..."
Price: 45.95 |
