SpoofCard Caller ID Spoofing Calling Card
| "Trend CRAFTPRO Single Flute Router Cutter 4.8mm 11.1mm 1/4""" |
| "Single fluted Tungsten Carbide straight cutter for fast free cutting. Single flutes should be chosen where speed and clearance rates are more important than the finish. Depth of cut should not exceed cutter diameter. D: 3/16 inch D: 4.8 mm C: 7/..."
Price: 13.95 |
| "Trend Extra Fine Three Flute Trimmer Bearing Guided Router Cutter 12.7mm 51mm 1/2""" |
| "Self-guiding triple flute cutter. Extra fine trimming and longer life. For trimming of laminate or plywood overlay etc. A 2mm maximum overlap should be left before trimming. D1: 1/2 inches D1: 12.7 mm C: 2 inches C: 51 mm B: 12.7 mm A: 90 de..."
Price: 64.95 |
| "Trend Undercut Router Cutter 25.4mm 6.3mm 1/4""" |
| "To produce an undercut on relief lettering to create a more aesthetic appearance, as well as for edge grooving. D: 1 inch D: 25.4 mm C: 1/4 inch C: 6.3 mm B: 12.7 mm OL: 55 mm E: 6.35 mm Shank Diameter: 1/4 inch Shank Diameter: 1/4 Dia ..."
Price: 39.95 |
| "Trend Bearing Guided Trimmer Router Cutter for Veneer 16mm 13mm 8mm" |
| "For trimming and bevelling timber, lippings and plastic laminate edges or any shaping applications. Self-guiding trimmer with bearings mounted on end of cutter. For trimming plastic or plywood overlay. For copy profiling, use the bearing to follow a ..."
Price: 24.95 |
| "Trend CRAFTPRO Two Flute Straight Router Cutter 50mm 25mm 1/2""" |
| "Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising. Use on softwoods, hardwoods, MDF, plywood and chipboard. Cutter has a bottom cut feature. D: 1 31/32 inch D: 50 mm C: 25 mm OL: 64 mm Shank ..."
Price: 54.95 |
| "Trend Lip and Spur Two Wing Machine Bit 38mm" |
| "These machine bits have two wings, two scribers and a centre point. Tungsten carbide tipped for extensive drilling of particle boards, and plastics of soft to medium density. The scribe gives a very clean entrance hole. Not for use on hard dense mate..."
Price: 63.95 |
| "Trend Glazing/Sash Bar Ovolo Joint Router Cutter 28.5mm 20mm 1/2""" |
| "Scribing cutter to suit glazing bar ovolo. Designed for sash bar window construction. Allows for a tenon on the sash bars. D: 28.5 mm C: 19 mm R: 17 mm OL: 57.2 mm Shank Diameter: 1/2 inch Shank Diameter: 1/2 Dia Metric: 28.5 Cut Length M..."
Price: 55.95 |
| "Trend CRAFTPRO Radius Router Cutter 12.7mm 19mm 1/2""" |
| "These cove style cutters with two flutes, give radiused grooves for decorative panel finishes and board edges. For deep channels, take a series of passes. DIMENSIONS: D1: 1/2 inches D1: 12.7 mm C: 3/4 inches C: 19 mm OL: 86 mm R1: 6.3 mm S..."
Price: 26.95 |
| "Trend Chamfer V Groove Router Cutter 25.4mm 13mm 1/2""" |
| "Use for bevelling, chamfering and for producing mortar grooves. Approximately 1.0mm flat will be found on the nose. D: 25.4 mm C: 13 mm C2: 17.5 mm A: 45 degrees OL: 57 mm Shank Diameter: 1/2 inch Shank Diameter: 1/2 Dia Metric: 25.4 Dia..."
Price: 48.95 |
| "Trend CRAFTPRO Radius Router Cutter 12.7mm 7.9mm 1/2""" |
| "These cove style cutters with two flutes, give radiused grooves for decorative panel finishes and board edges. For deep channels, take a series of passes. D: 1/2 inch D: 12.7 mm C: 5/16 inch C: 7.9 mm R: 6.3 mm OL: 48.5 mm Shank Diameter: 1/..."
Price: 17.95 |
| "Trend STC Spiral Upcut Router Cutter 7.9mm 12.7mm 1/2""" |
| "Ideal for use in CNC machines and for fixed head routing applications, can also be used in portable routers. Feed rates range from 5- 10m/min of 18000 - 24000 RPM. Ideal for hardwoods and abrasive material. Fine finish. Up-cut prevents burning in plu..."
Price: 98.95 |
| "Trend TRADE RANGE Staggered Mortise Router Cutter 16mm 1/2""" |
| "For deep mortising & grooving giving good chip clearance. Will plunge to a depth of 70mm in a number of passes. Features 2mm micrograin Tungsten Carbide tips, for cutting the most abrasive materials to give extra long life. PTFE coated, indicated by ..."
Price: 35.95 |
| "Trend CRAFTPRO Two Flute Straight Router Cutter 10mm 25mm 1/2""" |
| "Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising. Use on softwoods, hardwoods, MDF, plywood and chipboard. Cutter has a bottom cut feature. D: 25/64 inch D: 10 mm C: 25 mm OL: 69 mm Shank Di..."
Price: 15.95 |
| "Trend CRAFTPRO Bearing Guided Shoulder Profile Router Cutter 33.5mm 9mm 1/4""" |
| "For door and window construction, decorative panelling and many other joinery applications. D: 33.5 mm C: 9 mm B: 9.5 mm R: 9 mm OL: 64 mm Shank Diameter: 1/4 inch Shank Diameter: 1/4 Dia Metric: 33.5 Cut Length Metric: 9 Overall Length..."
Price: 45.95 |
| "Trend CRAFTPRO Bearing Guided Groove Router Cutter 12.7mm 12.7mm 1/4""" |
| "For veining, panelling, 'V' grooving, bevelling & chamfering. D1: 1/2 inches D1: 12.7 mm C: 1/2 inches C: 12.7 mm C2: 9 mm C3: 6 mm OL: 52.5 mm B: 12.7 mm A: 45 degrees Shank Diameter: 1/4 Shank Diameter: 1/4 Dia Metric: 12.7 Dia Imp..."
Price: 21.95 |
| "Trend Router Collet Reduction Sleeve 12mm 6mm" |
| "Reduction sleeve is used to reduce the collet size to take cutters with smaller shanks. Should only be used as a stop-gap, as the the correct size collet is recommended. Should not be used for extensive periods or heavy work. D: 12 mm OL: 30 mm ..."
Price: 14.95 |
| "Trend Replacement Cutter Bearings Metric OD 25mm" |
| "Bearings are shielded to prevent penetration of dust and grease packed for life. They should not be cleaned with solvent or lubricated as this will dissolve the grease and cause premature bearing failure. Scrape off any resin build-up. Always check t..."
Price: 11.95 |
| "Trend CRAFTPRO Two Flute Straight Router Cutter 9.5mm 19.1mm 1/2""" |
| "Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising. Use on softwoods, hardwoods, MDF, plywood and chipboard. Cutter has a bottom cut feature. D: 3/8 inch D: 9.5 mm C: 3/4 inch C: 19.1 mm OL: 6..."
Price: 11.95 |
| "Trend Mortar Groove Large Chamfer Router Cutter 38mm 27mm 1/2""" |
| "Use for producing mortar grooves and for bevelling applications. D: 38 mm C: 27 mm C2: 25.5 mm A: 60 degrees OL: 65 mm Shank Diameter: 1/2 inch Shank Diameter: 1/2 Dia Metric: 38 Cut Length Metric: 27 Overall Length Metric: 65 Angle: 60..."
Price: 53.95 |
| "Trend Guided Economy LaminateTrimmer Router Cutter 6.3mm 6mm 1/4""" |
| "Solid Tungsten Carbide economy cutter. Self guiding at 83 degrees with Ref. S48/41. The guide length is 3mm. D: 1/4 inch D: 6.3 mm C: 6 mm OL: 38 mm A: 83 degrees Shank Diameter: 1/4 inch Shank Diameter: 1/4 Dia Metric: 6.3 Dia Imperial..."
Price: 31.95 |
| "Trend CRAFTPRO Radius Bearing Guided Router Cutter 34.9mm 19.1mm 1/4""" |
| "Ideally suited for cutting radiused edges at speed, as a side fence can be dispensed with. The guide bearing follows the vertical edge or template. Alternative bearing Ref. B127A creates a shallow radius. D1: 34.9 mm C: 3/4 inches C: 19.1 mm B:..."
Price: 38.95 |
| "Trend Slow Spiral HSS Twist Drill 3/8""" |
| "Slow spiral is sometimes preferred for drilling end grain in wood. Ideal for fast drilling operations in open grained material. These drills are not for use with routers and not suitable for masonry work. D: 3/8 inch D: 9.5 mm OL: 130 mm Shank ..."
Price: 20.95 |
| "Trend WS Plug Maker 7/8"" 1/2""" |
| "Precision made plug makers for use on natural timber, exactly matching the holes produced by the Saw Tooth Forstners groups 1306 & 1307. These have four to six wings to ensure a clean cut. Use a slow, constant feed rate ensuring timber is clamped to ..."
Price: 86.95 |
| "Trend CRAFTPRO Bearing Guided Corner Bead Router Cutter 31.9mm 22.5mm 1/4""" |
| "Attractive edge moulds. A full corner bead can be produced by making a second pass at 90 degrees. D: 31.9 mm D2: 28.6 mm C: 22.5 mm B: 16 mm R: 7 mm OL: 72.5 mm Shank Diameter: 1/4 inch Shank Diameter: 1/4 Dia Metric: 31.9 Dia2 Metric: 28..."
Price: 37.95 |
| "Trend Threaded Slotter Blade for 33 Series M12 Arbors 50mm 11mm M12 Thread" |
| "These slotters have a M12 threaded boss to enable them to be threaded onto the arbor without the need for a securing nut. D: 50 mm Bore: M12 Kerf: 11 mm No. of Teeth: 4 Dia Metric: 50 Sawbore: M12 Saw Kerf Metric: 11 Saw Teeth: 4..."
Price: 67.95 |
| "Trend CRAFTPRO Two Flute Straight Router Cutter 7.5mm 25.4mm 1/4""" |
| ...
Price: 14.95 |
| "Trend TRADE Bearing Guided Trimmer Router Cutter 6.35MM 25.4mm 1/4""" |
| "For trimming and bevelling timber, lippings and plastic laminate edges. Features 2mm micrograin Tungsten Carbide tips, for cutting the most abrasive materials to give extra long life. PTFE coated, indicated by distinctive black colouring. Can be used..."
Price: 17.95 |
| "Trend Keyhole Slotter Router Cutter 12.7mm 4.9mm 1/4""" |
| "A keyhole recess for picture hanging flush to the wall. Ref. 35/01 - No.10 & No.12 screw heads. Not suitable for grooving applications. D: 12.7 mm D2: 8 mm S: 4.6 mm C: 4.9 mm OL: 38.1 mm Shank Diameter: 1/4 inch Shank Diameter: 1/4 Dia..."
Price: 34.95 |
| "Trend Finger Jointer Bearing Guided Router Cutter 24.6mm 18.5mm 1/4""" |
| "A bearing guided reversible finger jointer, to increase the gluing area for edge to edge joints. D: 24.6 mm C: 18.5 mm OL: 58 mm B: 12.7 mm Shank Diameter: 1/4 inch Shank Diameter: 1/4 Dia Metric: 24.6 Cut Length Metric: 18.5 Overall Len..."
Price: 56.95 |
| "Trend Aqua 63 Weatherseal Strip Brown 25m" |
| "Weather strip is fitted into the window frame aperture using four cut lengths. It is important to create tight butt or notched joints to ensure high levels of window performance. Joints can be enhanced by the application of a small amount of silicone..."
Price: 51.95 |
| "Trend Bearing Guided Rebater Router Cutter 35mm 12.7mm 1/2""" |
| "Popular rebate sets which include different size bearings for a choice of rebates. Ease of setting-up and accurate depth of cut. Ideal for rebating straight and shaped work pieces. Has a 60mm shank length to give access to deep rebates. When using be..."
Price: 74.95 |
