|
| |
| "Trend S49/2 x 1/4 STC Solid Carbide Cylinder Burr 10 x 20mm" |
"Solid carbide burrs and rasps for removing welds and burrs in metal and hand engraving and sculpting wood and metal. Ref S49/20 has no bottom cut. Recommended speed for mini burrs is 20, 000 - 90, 000 /min. TCT. 1/4in Shank."
Price: 32.23
|
|
| "Trend SNAP/D/SET 7 Piece Drill Set" |
"The snappy HSS Drill Bits are gripped by a spring steel collet into Hex Shaft. The Hex shanks snap into the quick chuck."
Price: 27.67
|
|
| "Trend SNAP/HD/Set Drill Set 7 Piece" |
"The HSS drill bits are gripped by a spring steel collet into the hex shaft. The hex shanks snap into the quick chuck. The hex collar is supplied in the sets to enable drills to be removed with two spanners. 7 piece drill set. 1.5, 2, 2. 5, 3, 4, 5 and 6mm. Supplied in a storage tube."
Price: 10.63
|
|
| "Trend 3/21 x 1/4 HSS Two Flute Cutter 6.3mm x 28mm" |
"Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods. Two flutes give a clean finish to cut edges. 1/4in Shank."
Price: 14.47
|
|
| "Trend C001 x 1/4 TCT Two Flute Cutter 3.2mm x 9.5mm" |
"Two fluted Tungsten Carbide Tipped straight cutters which are suitable for a wide range of applcations such a engraving, grooving, rebating and shallow morticing. They can be used on a wide range of materials such as softwoods, hardwoods, MDF, plywood and chipboard. All cutters are a TCT and have a bottom cut feature. When deep cuts are required, more than one pass should be taken. Shank: 1/4in."
Price: 15.11
|
|
| "Trend SET/SS9TC Starter Router Cutter Set of 15 1/2in Shank TCT" |
"Starter cutter set containing a range of 15 popular cutters supplied in a plastic carry case. Including: Single flute, two flute, dovetail, guided round and over guided chamfer, rebater, trimmer, cove and roman ogee, v groove and core box cutters. Size: 1/2in shank. Type: tungsten carbide tipped."
Price: 61.26
|
|
| "Trend SNAP/D/SET/2 1mm-7mm Drill Set 7 Piece" |
"The snappy HSS Drill Bits are gripped by a spring steel collet into Hex Shaft. The Hex shanks snap into the quick chuck."
Price: 27.67
|
|
| "Trend 13/3 x 1/4 TCT Radius Cutter 10.0mm Radius" |
"These cutters are used extensively for routing edge moulds, face grooves, columns, fluting, water slots, engraving and panel moulds in products such as desk tops, fire surrounds, draining boards and picture frames. These cutters are suitable for use on all natural timbers and man-made boards."
Price: 57.61
|
|
| "Trend 3/02 x 1/4 TCT Two Flute Cutter 6.3mm x 19mm" |
"Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods. Two flutes give a clean finish to cut edges. 1/4in Shank."
Price: 22.94
|
|
| "Trend 3/81 x 1/2 TCT Two Flute Cutter 12.7mm x 32mm" |
"Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods. T. C.T. Tooling1/2in Shank."
Price: 26.18
|
|
| "Trend 46/80 x 1/4 TCT 90° Bearing Guided Triple Flute Cutter 12.7 x 25.4mm" |
"Self-guiding triple flute cutters provide a super fine finish and longer life. Suitable for laminate or plywood overlay."
Price: 30.18
|
|
| "Trend B127A Replacement Bearing 1/2in Diameter 3/16in Bore" |
"Replacement bearing to suit all Trend bearing guided router cutters. The Bearings are shielded to prevent penetration of dust and grease packed for life and should not be cleaned with solvent or lubricated as this will dissolve the grease and cause premature bearing failure."
Price: 4.87
|
|
| "Trend Craftpro Credit Card Sharpening Stone" |
"The Trend CR/DWS/CC/FC is a double sided credit card size diamond stone. It has monocrystalline diamonds for fast, clean, stock removal and excellent sharpening performance. Double sided for coarse sharpening and fine honing. Coarse 360 grit (nom. 40 microns) and fine 600 grit (nom. 25 microns). Ideal for fluted, shaped and small router bits, carbide or HSS, turning tools, chisels, plane blades, carving tools and all general tooling. Recommended for use with Trend lapping fluid to prevent clogging or rusting and assist in keeping tools clean."
Price: 14.12
|
|
| "Trend Door Stand 32mm - 55mm D/STAND/A" |
"The Trend Door Stand holds door on its edge while routing hinge recess and mortice for locks. Holds door securely. Non-scratch base. Adjustable clamp for doors 32 to 55mm thick. Allows door to be tilted back to assist fitting into frame. Maximum door weight 50kg."
Price: 58.2
|
|
| "Trend Ellipse & Circle Cutting Jig Ellipse J/A" |
"Designed to enable virtually any router to cut ellipses and circles. Used for corner tables, arches, desks and mirrors. Setting-up and operating is simple and effective. A connector plate on the end of the bar fits directly onto the fence rods of Trend routers. For the fixing of other makes of routers, an accessory adaptor base plate is required. By using one slide, the jig can be adapted for cutting circles. With additional extension bars, larger ellipses and circles can be cut. Specifications: Ellipse major axis: 1800 mm. Ellipse minor axis max: 1650 mm. Ellipse minor axis min: 1400 mm. Ellipse major axis: 1500 mm. Ellipse minor axis max: 1350 mm. Ellipse minor axis min: 1100 mm. Ellipse major axis: 1200 mm. Ellipse minor axis max: 1050 mm. Ellipse minor axis min: 800 mm. Ellipse major axis: 900 mm. Ellipse minor axis max: 760 mm. Ellipse minor axis min: 550 mm. Ellipse major axis: 800 mm. Ellipse minor axis max: 650 mm. Ellipse minor axis min: 550 mm. Ellipse major axis: 700 mm. Ellipse minor axis max: 580 mm. Ellipse minor axis min: 580 mm. Circle dia. min: 580 mm. Circle dia. max: 1800 mm. Includes: 1 x cross frame, 2 x sliders, 2 x 500 mm bars and 1 x connector plate."
Price: 228.71
|
|
| "Trend SNAP/HKLC/6 Keyless Chuck" |
"The Trend SNAP/HKLC/6 Keyless Chuck can be used in quick chucks and impact drivers to hold parallel shank drills bits up to 1/4 inch. Clamping capacity: 0. 8 mm (1/32 inch) to 6 mm (1/4 inch). Enhanced gripping power when compared to traditional key type drill chucks. Lightweight with plastic body. Fitted with Snappy shank 1/4 inch hex shank adaptor. Specification Shank Diameter: 1/4in hex. Clamping Capacity: 0. 8-6mm (1/32-/14in)."
Price: 16.92
|
|
| "Trend VJS/CG/36 Clamp Guide 36in" |
"Integral clamping jaws and a locking lever provide a quick way of clamping the guide batten. It is ideal for holding and clamping work pieces and the aluminium extrusion incorporating T-slots. The clamp is fitted with a metric/imperial scale for setting lengths and stop positions and the scale can be be positioned by removing 20mm of the self adhesive backing."
Price: 43.02
|
|
| "Trend 334 x 1/2 TCT Aquamac Recessor" |
"Ref 334 recessing cutter will accomodate the Schlegal Aquamac 21 seal. This cutter is designed for use with the Aquamac seal in a wiping mode and comes complete with a guide bearing to reduce setting up time and simplify machining operations. Alternatively bearing Ref B35C is available to use the cutter for seals fitted in a compression mode of the seal. This larger bearing removes the rebate. TCT. Tooling : 1/2 Shank D = 54. 5 mmd = 34. 3 mm C1 = 10. 3 mm C2 = 2. 7 mm B = 28. 5 mm OL = 90 mm"
Price: 114.72
|
|
| "Trend 337 x 1/2 TCT Tongue & Groove Set 6.35mm x 10.0mm" |
"A one-piece tongue and groove set. The parts are inter-changed on the arbor to alter the set up. Maximum timber thickness 22 mm. Minimum timber thickness 15 mm. Instructions for use are supplied. TCT. 1/2in Shank. Slot Sizes 3. 35 mm - 10 mm. Max depth of slot 9. 5 mm"
Price: 79.97
|
|
| "Trend 8127 Collet Sleeve 8mm to 12.7mm" |
"Trend collet reduction sleeve, used to reduce the collet size to take cutters with smaller shanks. Should only be used as a stop-gap, as the correct size collet is recommended. Should not be used for extensive periods or heavy work."
Price: 13.81
|
|
| "Trend C115 x 1/4 TCT 90° Bearing Guided Trimmer Cutter 9.5 x 12.7mm" |
"Self-guided trimming bits. Used for trimming plastic or plywood overlays. Also for copy profiling with a template. Raise cutter in stages to spread wear of cutting edges D = 9. 5 mm C = 12. 7 mm"
Price: 17.71
|
|
| "Trend C130 x 1/4 TCT Bearing Guided Corner Bead 4.8mm Radius" |
"Attractive edge moulds and a full corner bead can be produced by making a second pass at 90° with this TCT cutter. Used on all man-made boards such as medium density fibre board, chipboard, and also natural timbers and most plastics. T. C.T. Shank = 1/4in. R = 4. 8 mm D = 26 mmd = 22 mm C = 16 mm B = 15. 9 mm Craft Range - They can be used on all man-made boards such as medium density fibre board, chipboard, and also natural timbers and most plastics Bead & Reed Cutters Bead and Reed cutters are ideally suited to form straight or curved decorative edge mouldings on table tops, chair legs and frames. They can also be used to produce complete round over profiles for window boards and stair tread nosings. Cutters can be combined to form compounded one-off mouldings for individual applications. Certain staff bead cutters are used to join boards and produce hinged joints for table tops."
Price: 42.65
|
|
| "Trend GB18 Guide Bush 18mm Dia E44178" |
"Trend guide bushes can be attached to the base of the Router. They are designed to follow the contours of a template."
Price: 10.6
|
|
| "Trend 12/3 x 1/4 TCT Radius Cutter 3.0mm Radius" |
"These cutters are used extensively for routing edge moulds, face grooves, columns, fluting, water slots, engraving and panel moulds in products such as desk tops, fire surrounds, draining boards and picture frames. These cutters are suitable for use on all natural timbers and man-made boards."
Price: 31.87
|
|
| "Trend 9/72 x 1/4 TCT Bearing Guided Corner Bead Cutter 4.8 Radius" |
"Bead Cutters are ideally suited to form straight or curved decorative edge mouldings on table tops, chair legs and frames. They can also be used to produce complete round over profiles for window boards and stair tread nosings. Cutters can be combined to form compounded one-off mouldings for individual applications."
Price: 66.85
|
|
| "Trend 9/73 x 1/2 TCT Bearing Guided Corner Bead Cutter 7.0 Radius" |
"Bead Cutters are ideally suited to form straight or curved decorative edge mouldings on table tops, chair legs and frames. They can also be used to produce complete round over profiles for window boards and stair tread nosings. Cutters can be combined to form compounded one-off mouldings for individual applications."
Price: 74.09
|
|
| "Trend C140 x 1/4 TCT Bearing Guided Corner Bead 3.2mm Radius" |
"Attractive edge moulds and a full corner bead can be produced by making a second pass at 90° . Used on all man-made boards such as medium density fibre board, chipboard, and also natural timbers and most plastics. D1 7/8 inch D1 22. 3 mm D2 20 mm Cut length 35/64 inch Cut length 14 mm B 12. 7 mm R1 3. 2 mm Shank Diameter 1/4 inch"
Price: 38.68
|
|
| "Trend Craft Dovetail Jig 600mm" |
"An accurate and easy-to-use dovetail jig for a variety of elegant dovetail joints. Cuts 12. 7mm (1/2in) wide half blind dovetails or rebated dovetails in one operation. Precision made, laser cut, zinc plated, steel template with packing piece. Adjustable offset stops. A Unibase and fine height adjuster may be required for certain makes of router. A range of accessory templates are available for box joint, dowel and through dovetails. Specification Rating: Craftsman. Dovetail Size: 12. 7mm. Workpiece Width Max: 600mm. Workpiece Thickness Min: 12mm. Workpiece Thickness Max: 25mm. Guide Bush Size: 15. 8mm. Router Base Diameter Max: 180mm."
Price: 259.45
|
|
| "Trend 12/5 x 1/4 TCT Radius Cutter 5.0mm Radius" |
"These cutters are used extensively for routing edge moulds, face grooves, columns, fluting, water slots, engraving and panel moulds in products such as desk tops, fire surrounds, draining boards and picture frames. These cutters are suitable for use on all natural timbers and man-made boards."
Price: 35.41
|
|
| |
|
