SpoofCard Caller ID Spoofing Calling Card
| "Trend TCT No Scriber Hinge Sinking Bit 35mm 3/8""" |
| "These machine bits are typically used by kitchen furniture manufacturers for recessing circular hinges. This type without scribers are for laminate covered boards. D: 35 mm OL: 65 mm Shank Diameter: 3/8 inch Shank Diameter: 3/8 Dia Metric: 3..."
Price: 50.95 |
| "Trend Bearing Guided Ovolo and Round Router Cutter 19mm 9.5mm 1/2""" |
| "Self-guiding cutters for rounding over edges do not require a side fence. They are supplied with two bearings. Use the larger bearing for a round-over. If the cutter is lowered, a top quirk can be produced. A full round/bullnose for stair treads can ..."
Price: 44.95 |
| "Trend Bearing Guided Intumescent Recess Router Cutter 40mm 25mm 1/2""" |
| "Bearing guided intumescent strip cutter for routing the groove for intumescent strip in a frame or door. A range of sizes available to suit 4mm thick strip from 10mm to 25mm width. Intumescent strip is used to create an effective barrier to both fire..."
Price: 77.95 |
| "Trend Trimmer Router Cutter 25mm 12mm 1/4""" |
| "Has three flutes, and has bevelled corners to prevent scoring, and is for flush trimming of hardwood or plastic edge strip. D: 25 mm C: 12 mm A: 90 degrees OL: 44.5 mm Shank Diameter: 1/4 inch Shank Diameter: 1/4 Dia Metric: 25 Cut Length M..."
Price: 50.95 |
| "Trend CRAFTPRO Wood Cutting Saw Blade 140mm 24T 20mm" |
| "A range of Tungsten Carbide Tipped Circular Sawblades designed for a professional finish in soft wood, hard wood, plywood, soft fibre, plasterboard stone, fibre board, cement bonded board and particle board. Reamed bore to ensure precise fit to spind..."
Price: 13.95 |
| "Trend Two Flute PTFE Coated Non Stick Router Cutter 15.9mm 19mm 1/4""" |
| "Gives a clean finish to abrasive materials such as chipboard, MDF, plywood and certain hardwoods. For housing, grooving and mortising. Features 2mm micrograin Tungsten Carbide tips, for cutting the most abrasive materials to give extra long life. PTF..."
Price: 22.95 |
| "Trend Replacement Cutter Bearings Metric OD 22mm" |
| "Bearings are shielded to prevent penetration of dust and grease packed for life. They should not be cleaned with solvent or lubricated as this will dissolve the grease and cause premature bearing failure. Scrape off any resin build-up. Always check t..."
Price: 11.95 |
| "Trend Chamfer V Groove Router Cutter 12.7mm 6.5mm 1/4""" |
| "Use for bevelling, chamfering and for producing mortar grooves. Approximately 1.0mm flat will be found on the nose. D: 12.7 mm C: 6.5 mm C2: 9 mm OL: 41 mm A: 45 degrees Shank Diameter: 1/2 inch Shank Diameter: 1/2 Dia Metric: 12.7 Dia ..."
Price: 22.95 |
| "Trend TCT Through Drill 201 Series 10mm 40mm 10mm" |
| "Tungsten carbide tipped dowel drill with V point . Suitable for drilling tear free through holes in natural wood and man-made boards (including paper/plastic coated and veneered). Drills have a cylindrical shank with flat and length adjusting screw. ..."
Price: 32.95 |
| "Trend STC Spiral Downcut Left Hand Router Cutter 12.7mm 38mm 1/2""" |
| "Down-cut spirals are ideal for routing small workpieces or for holding workpieces secure in vacuum jigs. Down-cut pushes woodchips below the work. Two flute. D: 1/2 inch D: 12.7 mm C: 38 mm OL: 89 mm Shank Diameter: 1/2 inch Shank Diameter:..."
Price: 104.95 |
| "Trend CRAFTPRO Bearing Guided Bevel Trimmer Router Cutter 25.4mm 10mm 1/4""" |
| "Two flute cutters for producing extra clean cut bevelled edges. No plunge cut. D: 1 inch D: 25.4 mm C: 25/64 inch C: 10 mm A: 60 degrees OL: 50 mm Shank Diameter: 1/4 inch Shank Diameter: 1/4 Dia Metric: 25.4 Dia Imperial: 1 Cut Length..."
Price: 19.95 |
| "Trend TCT Through Drill 201 Series 5mm 25mm 10mm" |
| ...
Price: 21.95 |
| "Trend CRAFTPRO Wood Cutting Saw Blade 180mm 30T 30mm" |
| "A range of Tungsten Carbide Tipped Circular Sawblades designed for a professional finish in soft wood, hard wood, plywood, soft fibre, plasterboard stone, fibre board, cement bonded board and particle board. Reamed bore to ensure precise fit to spind..."
Price: 15.95 |
| "Trend TCT Through Drill 201 Series Left Hand Rotation 10mm 25mm 10mm" |
| "Tungsten carbide tipped dowel drill with V point . Suitable for drilling tear free through holes in natural wood and man-made boards (including paper/plastic coated and veneered). Drills have a cylindrical shank with flat and length adjusting screw. ..."
Price: 26.95 |
| "Trend Bearing Guided Ovolo and Round Router Cutter 28mm 12.7mm 1/2""" |
| "Self-guiding cutters for rounding over edges do not require a side fence. They are supplied with two bearings. Use the larger bearing for a round-over. If the cutter is lowered, a top quirk can be produced. A full round/bullnose for stair treads can ..."
Price: 49.95 |
| "Trend Quad Groover Blade 47.6mm 6.3mm 1/2""" |
| "Replacement blade for QUADX1/2TC. D: 1 7/8 inch D: 47.6 mm E: 12.8 mm Kerf: 6.3 mm No. of Teeth: 2 Dia Metric: 47.6 Dia Imperial: 1 7/8 Rebate Metric: 12.8 Saw Kerf Metric: 6.3 Saw Teeth: 2..."
Price: 24.95 |
| "Trend Corner Bead Bearing Guided Router Cutter 23mm 20mm 1/4""" |
| "Creates a corner bead with a step. By making a second pass at 90 degrees a full corner bead can be cut. TCT featuring Dnamic carbide with extended life for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics. Two flutes gi..."
Price: 49.95 |
| "Trend CRAFTPRO Chamfer Bearing Guided Router Cutter 32mm 12.7mm 8mm" |
| "Self-guiding chamfer/bevel cutter. Bearing follows the board beneath. D: 32 mm C: 1/2 inch C: 12.7 mm B: 9.5 mm A: 45 degrees OL: 62 mm Shank Diameter: 8 mm Shank Diameter: 8 mm Dia Metric: 32 Cut Length Metric: 12.7 Cut Length Imperial:..."
Price: 25.95 |
| "Trend Bearing Guided Variable Kerf Groover 50mm 5mm 1/2""" |
| "To adjust the groove width these tools can be re-assembled with the supplied shims and spacers inserted between the groovers, giving a 0.1mm increment in thickness. D: 1 31/32 inch D: 50 mm C: 3-5 mm B: 28 mm E: 11 mm OL: 76 mm Shank Diamete..."
Price: 54.95 |
| "Trend Bearing Guided Template Profiler Router Cutter 16mm 19mm 8mm" |
| "Shank mounted bearing profilers are ideal for template guidance. Use for rebating and trimming edges only. Extra care must be taken to avoid cutter breakage. D: 5/8 inch D: 16 mm C: 3/4 inch C: 19 mm OL: 65 mm Shank Diameter: 8 mm Shank Di..."
Price: 22.95 |
| "Trend Replacement Cutter Bearings Metric OD 42mm" |
| "Bearing for slotting systems. Ball bearings should be wiped clean, not dipped in solvent. Prevent resin build-up by cleaning with wire brush. OD: 42 mm ID: 12 mm Thickness: 10 mm Cut Length Metric: 10 Bearing Dia Metric: 42 Sawbore: 12..."
Price: 12.95 |
| "Trend Drawer Pull Router Cutter 22mm 17mm 1/2""" |
| "Use in two passes from left & right to cut a protruding grip handle. D: 22 mm C: 17 mm R: 1.5 mm R2: 2 mm OL: 60 mm Shank Diameter: 1/2 inch Shank Diameter: 1/2 Dia Metric: 22 Cut Length Metric: 17 Overall Length Metric: 60 Radius 1 Me..."
Price: 72.95 |
| "Trend Intumescent Strip Recesser Bearing Guided Router Cutter 27.05mm 15mm 1/2""" |
| "Bearing guided intumescent strip cutter for routing the groove for intumescent strip in a frame or door. Two sizes available to suit 4mm thick strip of 10mm or 15mm width. Intumescent strip is used to create an effective barrier to both fire and smok..."
Price: 42.95 |
| "Trend Corner Bead Bearing Guided Router Cutter 22mm 18.9mm 1/4""" |
| "Creates a corner bead with a step. By making a second pass at 90 degrees a full corner bead can be cut. TCT featuring Dnamic carbide with extended life for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics. Two flutes gi..."
Price: 49.95 |
| "Trend Caravan Ind Guided Pierce and Trim Double Two Flute Router Cutter 12.7mm 24mm 1/2""" |
| "Combination pierce and trim cutters. Pierce and cut out apertures in laminate worktops. Base of the cutter acting as a guide follower. Will trim bottom and top laminate simultaneously. D: 1/2 inch D: 12.7 mm C: 24 mm C2: 24 mm OL: 126 mm Shan..."
Price: 50.95 |
| "Trend Leigh Dovetail Jig Router Cutter 7.9mm 9.5mm 1/4""" |
| ...
Price: 24.95 |
| "Trend Snappy Hex Shank HSS Drill Bit 4mm" |
| "The HSS drill bit is gripped by a spring steel collet into the hex shaft. The hex shanks snap into the Quick Chuck. D: 4 mm Shank Diameter: 1/4 inch hex Shank Diameter: 1/4 hex Dia Metric: 4..."
Price: 5.49 |
| "Trend CRAFTPRO Two Flute Straight Router Cutter 50mm 25mm 1/2""" |
| "Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising. Use on softwoods, hardwoods, MDF, plywood and chipboard. Cutter has a bottom cut feature. D: 1 31/32 inch D: 50 mm C: 25 mm OL: 64 mm Shank ..."
Price: 54.95 |
| "Trend Dovetail Router Cutter 9.5mm 8.5mm 1/4""" |
| "For dovetail joints and sliding dovetails. To suit user preference, the table shows angles from the horizontal and the profiles show angles from the vertical. D: 3/8 inch D: 9.5 mm C: 8.5 mm A: 102 degrees OL: 54 mm Shank Diameter: 1/4 inch ..."
Price: 31.95 |
| "Trend Bearing Guided Ovolo and Round Router Cutter 24.7m 12mm 8mm" |
| "Self-guiding cutters for rounding over edges do not require a side fence. They are supplied with two bearings. Use the larger bearing for a round-over. If the cutter is lowered, a top quirk can be produced. A full round/bullnose for stair treads can ..."
Price: 41.95 |
| "Trend Mini Guided Rebate Router Cutter 11.1mm 13mm 1/4""" |
| "Miniature bearing cutters ideal for sign-making, musical instrument building and other small intricate projects. Can be used on wood and plastic. Small bearing allows access to tight spaces and gives sharp corners. The unique design delivers a consta..."
Price: 22.95 |
