|
| |
| "Trend Replacement Bearings" |
"Replacement bearing to suit all Trend bearing guided router cutters. The Bearings are shielded to prevent penetration of dust and grease packed for life and should not be cleaned with solvent or lubricated as this will dissolve the grease and cause premature bearing failure."
Price: 4.37
|
|
| "Trend Biscuits" |
"Biscuit jointing has proven to be one of the strongest, fastest, safest and most accurate ways to join hard and soft woods, plywood, composition boards etc. Compared to dowelling, biscuit joinery is faster and more precise. The biscuits are made of laminated beech which is then compressed before being die cut. Beechwood biscuits expand up to 20 per cent when in contact with a woodworking adhesive. (e. g. PVA Glue)."
Price: 9.06
|
|
| "Trend Two Flute Cutters Craft Pro" |
"Two fluted Tungsten Carbide Tipped straight cutters which are suitable for a wide range of applcations such a engraving, grooving, rebating and shallow morticing. They can be used on a wide range of materials such as softwoods, hardwoods, MDF, plywood and chipboard. All cutters are a TCT and have a bottom cut feature. When deep cuts are required, more than one pass should be taken. Shank: 1/4in."
Price: 9.88
|
|
| "Trend 90° Bearing Guided Trimmer Cutter" |
"Self-guided trimming bits. Used for trimming plastic or plywood overlays. Also for copy profiling with a template. Raise cutter in stages to spread wear of cutting edges TCT. Diameter = 12. 7 mm Citting Length = 25. 4 mm"
Price: 18.59
|
|
| "Trend Guide Bushes" |
"Trend guide bushes can be attached to the base of the Router. They are designed to follow the contours of a template."
Price: 10.6
|
|
| "Trend Kitchen Worktop Jigs" |
"The Trend Kitchen Worktop Jig is a hard-wearing solid laminate, 12mm thick jig that enables cutting both parts of the joint in 15 minutes including setting up. The jig has the following features: Left and right hand corners, 400mm radius peninsular joint, 45° end cut with slight radius, 45° trade corner, 40mm radius corner, 35mm kitchen door hole and 3/4inch BSP hole for mixer taps. Engraved lines for 65mm bolts and worktop cross-cut. 6 x 10mm diameter ABS plastic pins with tapered shoulders for a tight fit and 3 point pin contact to ensure ease of setting up."
Price: 11.35
|
|
| "Trend Panel Butt Connectors" |
"Panel butt connectors to connect worktop joints together. Metal ended worktop connectors."
Price: 12.16
|
|
| "Trend Pocket Hole Jig" |
"The Trend PH/JIG Pocket Hole Jig is great for fast and accurate joining of timber and plywood, giving strong instant joints. Solid hardened bushes with variable pitch of 29mm to 63mm. Use on timber, MDF, plywood and block board. Allows a variety of joints to be created individually. Uses square drive self tapping screws. Work piece can be handled immediately after gluing and screwing, creating time saving benefits. No clamps required."
Price: 19.81
|
|
| "Trend 1/4in Two Flute Cutters Solid Carbide" |
"The Trend Solid Tungsten Carbide two flute cutters are turned, milled and ground from a solid piece of Tungsten Carbide and provide the greatest durability when used under stress load conditions. They offer better plunge cutting characteristics than TCT."
Price: 38.68
|
|
| "Trend Snap Countersinks" |
"The quick release drill system for drilling, countersinking and screwing designed for use with Power Drills and Screwdrivers and is compatible with direct-drive 1/4in Hex Shank Power Bits."
Price: 7.27
|
|
| "Trend Snap Countersink Sets" |
"The Trend Countersink Set contains five heat treated tool steel countersinks with hex shafts. They are fitted with High Speed Steel drill bits to cover the full range of screw sizes and are self clearing. They are adjustable for different length screws and will produce a 9. 5mm (3/8in) or 12. 7mm (1/2in) diameter counterbored hole to fit standard woodplugs. Contains: 1 x 2. 0mm (5/64in) Drill and C/S Size No. 4.1 x 2. 4mm (3/32in) Drill and C/S Size No. 6.1 x 2. 8mm (7/64in) Drill and C/S Size. No. 8.1 x 3. 2mm (1/8in) Drill and C/S Size. No. 10. 1 x 3. 6mm (9/64in) Drill and C/S Size. No. 12."
Price: 29.02
|
|
| "Trend Snap Centring Guides" |
"These spring loaded drill bit guides are self centring and are used for accurate drilling of holes for fittings such as hinges to ensure exact alignment. They can be easily dismantled for cleaning and are supplied with a HSS Drill Bit."
Price: 10.63
|
|
| "Trend Snap Plug Cutters" |
"Plug cutter for cutting plugs in Wood. Made from Tool Steel. Can be used in Snappy Quick chucks or directly in a standard chuck."
Price: 12.77
|
|
| "Trend T11EK Variable Speed Routers 1/2in" |
"T11 Variable speed workshop router with built-in Quick Raiser fine adjuster and electronic full wave variable control of spindle speed under load for a fine finish on all types of material. The soft start eliminates sudden movement of machine on start up and the two column precision base with large phosphor bronze bushes provides plunging accuracy. Spindle lock and hex collet nut results in easy cutter changes with the 22 mm spanner supplied. Adjustable twin rod parallel side-fence guide with integral micro-adjuster for straight edge work. Precision machined one-piece multi-slit collet for fail-safe grip of cutter shank. 3-position revolving depth stop for fast adjustable settings. Adjustable inner plate for guide bush accuracy. Router fine height adjuster for above and below height adjustment. One revolution of the handle equals 1. 5 mm. Three quick release recesses in base to fit tables in conjunction with optional Quick Release Kit. Fittings for optional Clamp Guide System Kit. Extra large base aperture for large cutters. Quick release dust spout. Specifications: Rating: Professional/Trade. Plunge stroke: 0-80 mm. Power input: 2, 000w. Collet diameter: 1/2 inch. No load speeds: 8-20, 000/min. Dust spout size: 35 mm. Guide bush dia. supplied: 30 mm. Cutter dia. max. plunge/table: 70/86 mm. Other collet dia. 6mm, 1/4in, 8mm, 3/8in, 10 mm & 12 mm. Weight 6. 3 kg."
Price: 507.38
|
|
| "Trend Replacement Filtres & Bags For T31A" |
"Replacement Filtres & Bags for the T31A Wet & Dry Vacuum."
Price: 5.39
|
|
| "Trend T5EB 1/4in Variable Speed Router 1000 Watt" |
"Trend T5EB 1/4 in and 8mm variable Speed Router with electronic full wave variable control of spindle speed under load for a fine finish on all types of material. Its soft-start feature eliminates sudden movement of machine on start up and thee is a spindle lock and hex collet nut that allows for easy cutter changes. The one-piece multi-slit collet with combined nut has been precision machined and it has a compact, lightweight design making it easy to use, especially for intricate work. Adjustable twin rod side-fence for guiding along a straight edge. Other features include: soft grip handles, low profile dust spout and ergonomic spindle lock. Specification Input Power: 1, 000 Watt. No Load Speed: 9-27, 000/min. Plunge Depth: 0-50mm. Max. Cutter Diameter: 40mm. Collet: 1/4in. Dust Spout Size: 35mm. Guide Bush Diameter: 20mm. Rod Diameter: 8mm. Rod Centres: 85mm. Weight: 3. 0kg."
Price: 142.5
|
|
| "Trend Two Flute Cutters Extra Long Shank" |
"Trend Trade range two flute router cutters have extra long shanks and are designed to meet the demanding needs of the professional trademen. They have a 2mm micrograin Tungsten Carbide tips for cutting the most abrasive materials to give extra long life. They have a PTFE coat, indicated by distinctive black colouring and produce a clean finish to abrasive timbers such as chipboard, MDF, plywood and certain hardwoods. The dimensions are etched on the extra long 40mm shanks for quick identification and are suitable for mortice and worktops applications."
Price: 25.52
|
|
| "Trend 1/4 drill diameter x 1/2 counterbore" |
"The CB counterbores are extensively used for recessing bolt and screw heads. Supplied with a HSS slow spiral drill bit. Fully adjustable, a hex key is supplied. Use a drilling speeds only. Not suitable for ferrous and non-ferrous metals. When setting-up, ensure flutes of drill are aligned with flute of counterbore. For replacement Twist Drills, use slow spiral type e. g 501/532 to 501/012. Specifications D=1/2 inch D=12. 7 mm D2=1/4 inch D2=6. 35 mm"
Price: 32.16
|
|
| "Trend 3/16 drill diameter x 3/8 counterbore" |
"The CB counterbores are extensively used for recessing bolt and screw heads. Supplied with a HSS slow spiral drill bit. Fully adjustable, a hex key is supplied. Use a drilling speeds only. Not suitable for ferrous and non-ferrous metals. When setting-up, ensure flutes of drill are aligned with flute of counterbore. For replacement Twist Drills, use slow spiral type e. g 501/532 to 501/012. Specifications D=3/8 inch D=9. 5 mm D2=3/16 inch D2=4. 76 mm"
Price: 30.23
|
|
| "Trend Bearing Guided Biscuit Jointer" |
"This TCT two wing slotting cutter is ideal for biscuit jointing sizes The set is supplied with 3 ball bearing guides to suit the three sizes of biscuits available. A slighlty longer cut than the length of the biscuit is required for ease of alignment during assembly Supplied with instructions. No. 0 - 45 mm x 15 mm x 4 mm Suitable for 8-12 mm boards Use bearing B19A 9. 05 mm depth No. 10 - 53 mm x 19 mm x 4 mm Suitable for 13-18 mm boards Use bearing B16A 10. 6 mm depth No. 20 - 58 mm x 23 mm x 4 mm Suitable for 19 mm + board Use bearing B127A D1 37. 2 mm Cut length 4 mm B 12. 7 mm B2 16. 0 mm B3 19. 0 mm"
Price: 39.31
|
|
| "Trend Craft saw blade 190mm x 40 teeth x 30mm" |
"A range of Tungsten Carbide Tipped Circular Sawblades designed for a professional finish in soft wood hard wood plywood soft fibre plasterboard stone fibre board cement bonded board and particle board Reamed bore to ensure precise fit to spindle Silverbraze to ensure tip is bonded securely to body Body hardened and tempered to maintain trueness Laser etched on reverse to European standard EN847-12 The Trend name for traceability and a guarantee of quality High grade alloy steel plate body precision ground to maintain flatness Microgranular Tungsten Carbide Tipped to allow cutting of abrasive materials Whats Included1 X 30-16mm bushing washer1 X 30-20mm bushing washer Specifications D7 12 inches D190 mm Bore30 mm Kerf26 mm Plate thick17 mm No of Teeth40Tooth form ATBHook15 degrees Quick Selector No15Colour Code Red Type Combination"
Price: 19.54
|
|
| "Trend Craft Pro sawblade panel trim 160mm x 48 teeth x 20mm Suitable for (Festool TS55)" |
"A range of Tungsten Carbide Tipped Circular Sawblades designed for a professional finish in soft wood hard wood plywood soft fibre plasterboard stone fibre board cement bonded board and particle board Reamed bore to ensure precise fit to spindle Silverbraze to ensure tip is bonded securely to body Body hardened and tempered to maintain trueness Laser etched on reverse to European standard EN847-12 The Trend name for traceability and a guarantee of quality High grade alloy steel plate body precision ground to maintain flatness Microgranular Tungsten Carbide Tipped to allow cutting of abrasive materials Specifications D6 14 inches D160 mm Bore20 mm Kerf22 mm Plate thick16 mm No of Teeth48Tooth form TCPHook4 degrees Quick Selector No71Colour Code Purple Type Panel Trimming"
Price: 24.95
|
|
| "Trend 11/3 x 1/4 TCT V Groove Cutter 45° 9.2 x 19.1mm" |
"Chamfer V grooving cutters are used for bevelling, chamfering and producing mortar grooves. Due to design, an approx. 1. 0 mm flat will be found on the nose. Typical trade applications include sign making, freehand engraving, cabinet making and decorative joinery."
Price: 29.56
|
|
| "Trend 3/83 x 1/2 TCT Two Flute Cutter 12.7mm x 50mm" |
"Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods. T. C.T. Tooling1/2in Shank."
Price: 33.67
|
|
| "Trend T46/1 x 1/4 TCT 90° Template Profiler 15.9 x 13mm" |
"Self guiding cutters with bearings mounted for trimming and bevelling timber, lippings and plastic laminate edges for cabinet making, countertop production or any shaping applications. Bearing guided cutters are suitable for both straight and curved work, bearings are normally fractionally larger than cutter diameter, to avoid surface scoring. Uses: Trimming plastic or plywood overlay. Copy profiling - use the bearing to follow a template or base edge of board. A 3 mm approximate overlap should be left before copy profiling, also when using plastic laminate always allow laminate adhesive to dry before trimming. This avoids clogging the guide bearing. Tooling Tungsten Carbide1/2in Shank."
Price: 28.19
|
|
| "Trend VJS/CG/50 VariJig Clamp Guide 50in" |
"The Trend VJS/CG/50 Vari Jig clamp guide allows for accurate guiding of router, saws and jigsaws. Its integral clamping jaws and a locking lever provide a quick way of clamping the guide batten and is ideal for holding and clamping workpieces. The aluminium extrusion incorporates T-slots. The clamps are fitted with a metric/imperial scale for setting lengths and stop positions. Scale can be positioned by removing 20mm of the self-adhesive backing. Router not included. Patent No. US7, 007, 731."
Price: 49.16
|
|
| "Trend 1/2in Two Flute Cutters TCT" |
"Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods. T. C.T. Tooling1/2in Shank."
Price: 25.57
|
|
| "Trend Helical Plunge Bits HSSE" |
"Tooling for use on webbed aluminium and UPVC extrusions by window and door fabricators. Cutters are produced in special high speed steel (HSSE) to ensure a clean cut and resist the abrasive nature of anodised aluminium extrusions. Cutters are designed to plunge and machine or mill lateral slots All tooling for aluminium should be used with a coolant, wax stick, or lubricant. The material being worked on should always be securely clamped in a machine vice. HSSE. One Flute helical Plunge-slotting bit."
Price: 18.34
|
|
| "Trend 9/7 Bearing Guided Corner Bead Cutters" |
"Bead Cutters are ideally suited to form straight or curved decorative edge mouldings on table tops, chair legs and frames. They can also be used to produce complete round over profiles for window boards and stair tread nosings. Cutters can be combined to form compounded one-off mouldings for individual applications."
Price: 54.35
|
|
| |
|
