| "Trend CRAFTPRO Radius Bearing Guided Router Cutter 50.8mm 25.4mm 1/2""" |
| "Ideally suited for cutting radiused edges at speed, as a side fence can be dispensed with. The guide bearing follows the vertical edge or template. D1: 50.8 mm C: 1 inches C: 25.4 mm B: 12.7 mm R1: 3/4 inches R1: 19.1 mm OL: 75 mm Shank Dia..."
Price: 55.95 |
| "Trend Roman Ogee Bearing Guided Router Cutter 25.4mm 15.9mm 1/2""" |
| "With bearing guided ogees, change profile by using a larger bearing and vary the depth. D: 1 inch D: 25.4 mm C: 5/8 inch C: 15.9 mm B: 9.5 mm B2: 12.7 mm R: 4 mm OL: 63 mm Shank Diameter: 1/2 inch Shank Diameter: 1/2 Dia Metric: 25.4 ..."
Price: 45.95 |
| "Trend Eccentric Single Flute Router Cutter 4.8mm 19mm 1/2""" |
| "Eccentric single flute cutters. Cutters are chosen for fast free cutting, when cutting speed takes preference over finish. Small diameter tools must be handled with care to avoid breakage. Single flute cutters should not be used in eccentric chucks. ..."
Price: 28.95 |
| "Trend CRAFTPRO Chamfer Bearing Guided Router Cutter 32mm 12.7mm 1/2""" |
| "Self-guiding chamfer/bevel cutter. Bearing follows the board beneath. D: 32 mm C: 1/2 inch C: 12.7 mm B: 9.5 mm A: 45 degrees OL: 60 mm Shank Diameter: 1/2 inch Shank Diameter: 1/2 Dia Metric: 32 Cut Length Metric: 12.7 Cut Length Imperi..."
Price: 28.95 |
| "Trend Flat Ovolo Router Cutter 25mm 8mm 1/4""" |
| "Panel mould and edge mould cutter. D: 25 mm C: 8 mm R: 12 mm OL: 36.6 mm Shank Diameter: 1/4 inch Shank Diameter: 1/4 Dia Metric: 25 Cut Length Metric: 8 Overall Length Metric: 36.6 Radius 1 Metric: 12..."
Price: 40.95 |
| "Trend CRAFTPRO Wood Cutting Mitre Saw Blade 250mm 42T 30mm" |
| "A range of Tungsten Carbide Tipped Circular Sawblades designed for a professional finish in hard wood, exotic rip, plywood rip, crosscut, softwood rip and chipboard laminated one-sided. Reamed bore to ensure precise fit to spindle. Silverbraze to ens..."
Price: 22.95 |
| "Trend Replacement Cutter Bearings Metric OD 19mm" |
| "Bearings are shielded to prevent penetration of dust and grease packed for life. They should not be cleaned with solvent or lubricated as this will dissolve the grease and cause premature bearing failure. Scrape off any resin build-up. Always check t..."
Price: 11.95 |
| "Trend WS Long Series Saw Tooth Forstner Drill Bit 1"" 1/8"" 1/2""" |
| "Saw Tooth Forstner bits are made from high grade Carbon Steel and meticulously heat treated. They cut fast, with the grain or across it. They can drill overlapping holes in any direction and are chosen for exacting and delicate work, such as scroll a..."
Price: 34.95 |
| "Trend Two Flute PTFE Coated Non Stick Router Cutter 3.2mm 12.7mm 8mm" |
| "Gives a clean finish to abrasive materials such as chipboard, MDF, plywood and certain hardwoods. For housing, grooving and mortising. Features 2mm micrograin Tungsten Carbide tips, for cutting the most abrasive materials to give extra long life. PTF..."
Price: 17.95 |
| "Trend CRAFTPRO Two Flute Straight Router Cutter 19.1mm 19.1mm 8mm" |
| "Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising. Use on softwoods, hardwoods, MDF, plywood and chipboard. Cutter has a bottom cut feature. D: 3/4 inch D: 19.1 mm C: 3/4 inch C: 19.1 mm OL: ..."
Price: 14.95 |
| "Trend CRAFTPRO Stepped Rebate Router Cutter 9.5mm 13mm 1/2""" |
| "Recessing cutter for producing double rebates. For producing recesses with a lower rebate. Designed to accept library/bookcase strip. Specifically designed for Tonk Strip. D: 9.5 mm D2: 19 mm C: 13 mm C2: 6 mm OL: 57 mm Shank Diameter: 1/2 i..."
Price: 29.95 |
| "Trend CRAFTPRO Two Flute Straight Router Cutter 12.7mm 50mm 1/2""" |
| "Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising. Use on softwoods, hardwoods, MDF, plywood and chipboard. Cutter has a bottom cut feature. D: 12.7 mm C: 50 mm OL: 93.5 mm Shank Diameter: 1/2..."
Price: 25.95 |
| "Trend Two Flute PTFE Coated Non Stick Router Cutter 6.35MM 25mm 1/4""" |
| "Gives a clean finish to abrasive materials such as chipboard, MDF, plywood and certain hardwoods. For housing, grooving and mortising. Features 2mm micrograin Tungsten Carbide tips, for cutting the most abrasive materials to give extra long life. PTF..."
Price: 19.95 |
| "Trend TRADE Bearing Guided Trimmer Router Cutter 6.35MM 12.7mm 1/4""" |
| "For trimming and bevelling timber, lippings and plastic laminate edges. Features 2mm micrograin Tungsten Carbide tips, for cutting the most abrasive materials to give extra long life. PTFE coated, indicated by distinctive black colouring. Can be used..."
Price: 16.95 |
| "Trend Bearing Guided Trimmer Router Cutter 12.7mm 25mm 1/4""" |
| "For trimming and bevelling timber, lippings and plastic laminate edges or any shaping applications. Self-guiding trimmer with bearings mounted on end of cutter. For trimming plastic or plywood overlay. For copy profiling, use the bearing to follow a ..."
Price: 23.95 |
| "Trend CRAFTPRO Two Flute Straight Router Cutter 6.3mm 12.7mm 1/4""" |
| "Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising. Use on softwoods, hardwoods, MDF, plywood and chipboard. Cutter has a bottom cut feature. D: 1/4 inch D: 6.3 mm C: 1/2 inch C: 12.7 mm Ol: 5..."
Price: 10.95 |
| "Trend CRAFTPRO Two Flute Straight Router Cutter 9.5mm 31.8mm 1/2""" |
| "Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising. Use on softwoods, hardwoods, MDF, plywood and chipboard. Cutter has a bottom cut feature. D: 3/8 inch D: 9.5 mm C: 1 1/4 inches C: 31.8 mm O..."
Price: 12.95 |
| "Trend Planer Blade Conversion Kit 82mm" |
| "Contains a pair of plates to allow the PB/29 blades to be fitted into the planer cutter block for certain Makita, Hitachi and Kango planers. Required for following:- Hitachi F20, FU20 Makita M102, 1900, 1900B, 1901, 1125, 1100, 1923B, 1923BD Ryobi L1..."
Price: 11.95 |
| "Trend Cove Bearing Guided Router Cutter 63.5mm 25.4mm 1/2""" |
| "The two bearings supplied offer the means of cutting different depths of mouldings. D: 63.5 mm C: 1 inch C: 25.4 mm B: 12.7 mm B2: 16 mm R: 1 inch R: 25.4 mm OL: 90.9 mm Shank Diameter: 1/2 inch Shank Diameter: 1/2 Dia Metric: 63.5 Cu..."
Price: 81.95 |
| "Trend Aluminium UPVC Single Flute Helical Upcut Cutter 5mm 14mm 8mm" |
| "Cutter are designed to plunge and machine or mill lateral slots. All aluminium tooling should be used with a coolant, wax stick or lubricant. Material should be securely clamped. Single flute helical for drilling and slotting, cutting aluminium anodi..."
Price: 26.95 |
| "Trend Threaded Slotter Blade for 33 Series M12 Arbors 50mm 6mm M12 Thread" |
| "These slotters have a M12 threaded boss to enable them to be threaded onto the arbor without the need for a securing nut. D: 50 mm Bore: M12 Kerf: 6 mm No. of Teeth: 4 Dia Metric: 50 Sawbore: M12 Saw Kerf Metric: 6 Saw Teeth: 4..."
Price: 60.95 |
| "Trend Acrylic Template Material 8mm" |
| "Square sheet of clear acrylic for use when making routing templates and jigs. Can be sawn, routed with TCT tools and drilled easily. Size: 8 x 495 x 495 mm Cut Length Metric: 8..."
Price: 38.95 |
| "Trend Bull Nose Undercut Combination Router Cutter 67mm 25mm 12mm" |
| "Especially designed for routing Corian, and similar luxury 'marble like' material which is used in many bathrooms and kitchens. For bullnose moulding use Ref. 90/20 inconjunction with Ref. 90/25. D: 54 mm C: 20 mm B: 28.57 mm R: 12.7 mm OL: 73..."
Price: 88.95 |
| "Trend CRAFTPRO Aluminium and Plastic Cutting Saw Blade 215mm 64T 30mm" |
| "A range of Tungsten Carbide Tipped Circular Sawblades designed for a professional finish in plastic & alloy. Reamed bore to ensure precise fit to spindle. Silverbraze to ensure tip is bonded securely to body. Body hardened and tempered to maintain tr..."
Price: 28.95 |
| "Trend Large Flat Roman Ogee Router Cutter 41.5mm 8mm 1/2""" |
| "Flat Roman Ogee, for raised panelling or edge moulding. Used for decorative capping on hand rails. D: 41.5 mm C: 8 mm C2: 8 mm R: 19 mm R2: 11 mm OL: 56 mm Shank Diameter: 1/2 inch Shank Diameter: 1/2 Dia Metric: 41.5 Cut Length Metric:..."
Price: 72.95 |
| "Trend CRAFTPRO Two Flute Straight Router Cutter 6mm 16mm 8mm" |
| "Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising. Use on softwoods, hardwoods, MDF, plywood and chipboard. Cutter has a bottom cut feature. D: 15/64 inch D: 6 mm C: 5/8 inch C: 16 mm Ol: 60...."
Price: 9.95 |
| "Trend Ogee Router Cutter 33mm 23mm 1/4""" |
| "Cutters for false panels or edge moulds. Curved work possible in fixed head router and copy follower. D: 33 mm D2: 8 mm C: 23 mm R: 7.2 mm OL: 51.6 mm Shank Diameter: 1/4 inch Shank Diameter: 1/4 Dia Metric: 33 Dia2 Metric: 8 Cut Length..."
Price: 50.95 |
| "Trend Threaded Arbor For M12 Bore Groover Blades 1/2""" |
| "Slotters with M12x1.0 threaded bore enables flush recessing in the corner such as for weather proofing. Spacers are supplied to ensure the minimal threaded arbor protrudes below the slotter. Arbor 33/20 enables 12mm bore guide bearings to be fitted a..."
Price: 13.95 |
| "Trend Dovetail Cutter for DC400 Jig 11.3mm 19mm 8mm" |
| "Cutters for use with the Trend DC400 Dovetail Jig. These cutters have extra long shanks. D: 11.3 mm C: 19 mm A: 97 degrees OL: 68 mm Shank Diameter: 8 mm Shank Diameter: 8 mm Dia Metric: 11.3 Cut Length Metric: 19 Overall Length Metric: ..."
Price: 19.95 |
| "Trend WS Plug Maker 1/2"" 1/2""" |
| "Precision made plug makers for use on natural timber, exactly matching the holes produced by the Saw Tooth Forstners groups 1306 & 1307. These have four to six wings to ensure a clean cut. Use a slow, constant feed rate ensuring timber is clamped to ..."
Price: 73.95 |
| "Trend Panel Mould Wide Ogee Router Cutter 25mm 10mm 1/4""" |
| "Panel raisers can be used with guide bush templates for decorative work on panel doors etc. D: 25 mm D2: 10 mm C: 3/8 inch C: 9.5 mm R: 3.2 mm OL: 49 mm Shank Diameter: 1/4 inch Shank Diameter: 1/4 Dia Metric: 25 Dia2 Metric: 10 Cut Le..."
Price: 57.95 |
